How to Solder Waterproof Wiring to Pixel Strings (Video)

Worried about how to solder your waterproof extension cables to your pixel strings?  Worry no more, the following video shows how simple it is to solder on wiring to your pixels:

The following products were used in this video:

10ft, 3 core extension cable
12v, WS2811 Pixel String
1/8" Heat Shrink Tubing
3/8" Heat Shrink Tubing

Is a RGB Pixel Package A Good Choice for My RGB Project?

A very common question we get is - does HolidayCoro have a package or kit of RGB pixel items that can be used for RGB projects.  This blog post hopes to be able to provide you with sound advice about when a "package" or kit is a good choice and when it isn't a good choice for you and your project.  This article is a follow-up to our "Cheap Isn't Free When It Comes To RGB" blog post which talks about the pros and cons of DIY vs vendor developed solutions from a time and cost perspective.  First, let's start off with defining the project you plan to build - while there are many different types of projects that involve RGB and/or pixels - in this article we will use the two most popular uses of pixels today and the ones for which we receive the most questions about:

• Outline a House (soffit, fascia, roof line, windows, etc) with pixels (covered in this blog post)
• Building a pixel MegaTree

Outlining A House with Pixels

Each time we work with a customer on a house outline there are many common items/questions for all installations - length (linear feet) of area to cover, density of control (pixels per meter or inch), budget, controllers and the overall look the customer wants to achieve.  Let's start with these and look at the different options:

• Length of area to cover - There is never a single length for any house type because each house has different lengths and each customer wishes to outline different areas (windows or no windows, roof line or no roof line).  As such, any "package" deal would need to have the specific amount of lighting for that specific installation.  Additionally, other factors such as long run lengths that might need 12v lights instead of 5v lights can also factor into the decision based on the design of the house.
• Density of control - Some displays are viewed from hundreds of feet away, others are viewed from tens of feet - as such, the value of specific pixel density (30 LED/m vs., say 48 LED/m or 60 LED/m) changes from display to display.  Additionally, with different density comes different sequencing and bandwidth requirements, which, depending on the display, can be an important factor.
• Budget - Each person's budget is different and that factors into how they design their display.  Some customers will want nice moulded waterproof connections on lights, others are satisfied by basic, non-waterproof connections.
• Controllers - The number and type of controllers will vary depending on the physical layout of the house.  Sometimes it can be be cheaper and easier to install more controllers than less due to the amount of additional wiring that would be required to support just one controller.

As you can see, even with just this small subset of factors that go into the proper design of a house outline - there will never be the same "package" for each house because there are just too many variables involved.

For house outlines, you'll either need to use a guide like our, how-to blog post on the subject to design your own or use a design service offered by some vendors that look at your specific needs and then can recommend the exact right combination of hardware for your house.  Currently no other vendor other than HolidayCoro offers custom house outline services.  As HolidayCoro attempts to strike a balance as we are a low-margin hardware vendor we offer design services as an additional for fee service which can be found here:  https://www.holidaycoro.com/Services-Consulting-s/1858.htm

For a representation of the hardware in a common house outline, see:  https://www.holidaycoro.com/RGB-House-Outline-Packages-s/1967.htm 

Pixel MegaTree

A pixel MegaTree is a very common project for many displays.  A pixel MegaTree is pretty much just a large matrix of pixels, wrapped around a cone and is used to display effects.  There are a number of inputs into a MegaTree and they are:

• Height and Width of the MegaTree - Typically a "package" MegaTree will be set for a specific height because the diameter of the tree along with the spacing of the pixels in the package determine the final overall height.  If the size of the tree and the mounting method used to build that tree work well for you, a package may be a good choice.  If you have specific spacing requirements, such as the high density needed to display readable, scrolling text, the pixels included with a package may not be the best choice.  Additionally, if you have specific needs such as a smaller tree due to a small yard or close proximity to your audience, or, if your display is huge and you need something more in "scale" with your other display items, a packaged design likely isn't a good choice.
• Pixel Type - The type of pixel used on a MegaTree greatly affects the overall look and functionality of the MegaTree.  Choices can include nodes, strip or even bulbs.  Each physical type of pixel has a pro and con.
• Controller / Power - Since MegaTrees are typically full (360 degree) or half (180 degree) cones, it makes sense to have the power and controller centrally located in the trunk and thus most packages include a controller, power supply(s) and mounting box.

So, while a MegaTree does allow for some level of "standardization" to allow for it to be put into a package, make sure that package meets your pixel type and density requirements - if your specific needs, such as height, spacing or node type differ, you'll likely be better off with a custom solution instead of a package.

HolidayCoro offers common pixel tree formats of 50 pixels x 12 or 50 pixels by 16 in strips and nodes:  https://www.holidaycoro.com/RGB-Pixel-Mega-Tree-Packages-s/1964.htm

If your needs are more specific, HolidayCoro can also design a MegaTree based on your specific project requirements through our consulting service: https://www.holidaycoro.com/Services-Consulting-s/1858.htm

A Demonstration of the Effects of Power Draw on Long Lengths of RGB Lights

Todays blog post is about the effects that power draw has on RGB lights.  We've taked about it before in our blog post about how wiring affects power distribution and in our demonstration example house where we lined it with pixels and handled the issue of power consumption.

This video is pretty simple - it shows 160 pixels (480 DMX channels) connected to a single power supply and our HolidayCoro pixel controller.  It is intended to show the effects that the gauge of the power wire and the power consumption of the pixels themselves have on the actual light output.


(open in YouTube with High Def for better viewing)

Post any questions below.

Thanks,
David
HolidayCoro.com

Outlining Your House in RGB Lights - Detailed Design Guide (Updated for 2026)

Updated September 2026. We rewrote this guide around the pixels, mounting and controllers we recommend today. The original 2013 version was built around pixel strip and hardware that has since been replaced.

When you're planning a Christmas display, it's easy to focus on everything going in the yard. But the biggest prop is already there: your house. Outline it, and the house becomes part of the sequence, framing everything you've built in front of it.

Vineyards Lights, Meridian, ID. The rooflines, peaks and garage all become part of the show.

If you want the big picture first (why a mounting system matters and how to pick between seasonal and permanent), start with our house outline primer. This post is the step-by-step design: how to measure, how many pixels you need, how to power them and where the controller goes.

Would you rather have us do the math? Fill out our project design form and we'll send you instructions for sending us one photo of your house and your measurements. We'll put together a recommendation and a complete quote with the controller, mounting, hardware and accessories for your project.

Step 1: Start with a photo

Go outside and take a photo of your house from where your audience will see it, usually the street. You'll sketch your design on this photo and use it to record measurements, where cables will run and where the controller and power supplies will go.

We'll use Nathanial R.'s house as our example throughout. It has 19 separate rooflines, so it's a good example of how a house with complex roof lines can be handled.

Step 2: Measure every run

Get out the ladder and tape measure and record the exact length of every section you want to outline. Write each one on the photo.

Accuracy matters. Every foot you miss is another 4 pixels at 3 inch spacing, which changes your pixel count, your power budget and possibly how many controller outputs you need.

Step 3: Choose seasonal or permanent mounting

Across a whole house, mounting pixels one at a time means a lot of clips, a lot of alignment and a lot of visible black wire. A mounting system lets you build the outline in sections that hold their spacing and aim, snap into a few clips and come down as a unit for repairs.

Want it to come down after Christmas? Use Pixel Pipe. Each aluminum pipe is 7.3 feet long with 88 holes on 1 inch centers, sized for standard 12mm bullet pixel nodes. It's available in black, white or mill-finish grey, mounts with clear, UV-resistant clips that can stay on the house year-round, and rotates in its clips so you can aim the pixels toward your viewing area. Couplers, corners and tees let you follow the roofline.

Want it to stay up? Use PixaTrack. Each track is 6.66 feet long with 80 holes on 1 inch centers and takes 12mm bullet or square-neck nodes. It fully encloses the wiring to protect it from UV and animals, comes in off-white or brown to blend with the house, and is available with front-facing or side/down-facing holes.

Both come as samples, so you can hold one up against your house before you decide.

Step 4: Pick your spacing and count your pixels

Because both systems are drilled on 1 inch centers, you can space pixels at 1, 2, 3 inches or more by skipping holes. Two things set how far apart you can go:

• The wire length between nodes on the pixel string. Our 100-count 12mm node strings reach up to about 3.4 inches between nodes. For wider spacing, our 6 inch strings reach up to about 6.8 inches.
• The look you want. Closer spacing reads as a solid line and gives you more resolution for effects. Wider spacing costs less and gives a more classic bulb-by-bulb look.

The math is simple:

Pixels = run length in inches ÷ spacing in inches
DMX channels = pixels × 3

For Nathanial's house we grouped the 19 measured sections into four continuous runs and used 3 inch spacing:

Run	Length	Pixels (3" spacing)	DMX channels	Watts at full white
Garage front	26 ft	104	312	57
Garage, over the doors	34 ft	136	408	75
Front of house, upper	53 ft	212	636	117
Front of house, lower	31 ft	124	372	68
Total	144 ft	576	1,728	317

At 170 pixels per DMX universe, 576 pixels needs 4 universes. Any current E1.31 pixel controller handles that over a single network cable.

Step 5: Plan your power

Our 12v, 12mm nodes draw about 0.55 watts each at full white (45 milliamps). That's where the watts column above comes from: 576 pixels × 0.55 W = about 317 watts, or roughly 26 amps at 12 volts. Size your power supplies with headroom above that number, since draw varies with temperature, wiring and supply voltage.

The second question is how far the power can travel. As power runs down a string, voltage drops through the LEDs and the wire itself. Our 100-count node strings are designed to run the full 100 nodes with power fed at the start. Past that, plan to inject power. Three of the four runs above are over 100 pixels, so each would get power injection partway along, or be split into two shorter runs fed from separate outputs.

To inject, run heavier-gauge wire (14 AWG is a good start) from the power supply to the injection point and connect it to the power and ground of the string there. The data passes straight through, since each pixel regenerates it. See our guide to wire selection for sizing the injection wire.

Test before it goes on the house. Build a section, set it to full white for 15 to 30 minutes and measure the voltage at the controller output and at the last pixel with a multimeter. A drop of 10 to 20% is usually fine. Much more than that and you'll see dimming or color shift at the end of the run, or random flicker if the voltage falls below what the pixel chips need. Finding that on the ground is a lot easier than finding it on the roof.

Step 6: Place the controller

Look at your photo for where runs start and end. Places where two runs meet, like a garage corner or the peak over a front door, are natural spots to feed two outputs from one location. Current pixel controllers and sequencing software let you reverse a run's direction, so a run can start at either end.

The data signal from a pixel controller output only travels a limited distance to the first pixel, so you have two basic layouts:

• One central controller. An AlphaPix Classic with 4 or 16 outputs, placed somewhere central and close to the runs. It keeps everything in one enclosure, and spare outputs can drive other props in the yard.
• A controller plus long-range receivers. With a Flex system, the controller can sit in the garage and small long-range receivers go near the roofline where the runs start. This is the better fit for large houses, runs that start far apart, or when you want the main controller out of sight.

For Nathanial's four runs and about 317 watts, a single 4-output controller placed near the garage corner would handle the whole outline. Adding props later, or splitting the long runs, is where a 16-output controller or a Flex system with receivers starts to make sense. Our Controller Selection Wizard walks you through the options.

Step 7: Build and test on the ground

One of the biggest advantages of Pixel Pipe and PixaTrack is that you can build each section on the ground, plug it in and test it before it goes up. With connectors between sections, a problem later means unplugging one section, fixing it in the garage and putting it back without disturbing your spacing. With a seasonal install, the sections come down as a unit and go back up next year exactly as they were.

Watch the full process

Our house outline video walks through planning and building an outline with Pixel Pipe and PixaTrack from start to finish:

Let us put it together for you

You don't have to work out every part of the system yourself. Fill out our project design form and we'll send you instructions for sending one photo of your house and your measurements. We'll look at what you're planning and put together a recommendation and a complete quote with the controller, mounting, hardware and accessories you'll need.

Want to see the mounting in person first? Pixel Pipe and PixaTrack samples let you compare colors against your house before choosing a system.

HolidayCoro.com

The Good, Bad and the Future: Pixel Nodes



Channel Letter Sign with 8mm Pixel Nodes

8mm Tri-Color RGB Node with 12mm Case

First, a little background on the 8mm, tri-color LED node.  For anyone that has been to Asia (mainly China), you'll notice that they have many signs produced that use these nodes.  These signs are what we would, in the US, call Channel Letter signs.  In the US, we normally have channel letter sign that has an acrylic face with sheet metal sides and back that form a box, which is then illuminated with either neon (older) or LED modules (newer).  This channel letter design in the US produces a smooth clean, single color letter. 

While China also has the same type of channel letter signs, they also have the same sign but instead of an acrylic face they again use sheet metal for the face.  In that sheet metal they then punch ~12mm holes.  In these holes they install either dumb or intelligent RGB nodes.  This creates a sign that can be addressed either as a matrix (intelligent pixels) or just as a single color (dumb).  This type of sign design is nearly non-existent in the US currently.  So, why does this matter?  Well, this explains first why the physical case of nodes are generally 12mm in diameter.  It also explains why the little "fingers" that are on the side of the nodes are only about 1/16 of an inch between the top and bottom - they are design to fit into thin gauge sheet metal and pretty much nothing else. 

Here is the problem - they often are not exactly the same diameter, either from a single vendor, even within a single string or very often from vendor to vendor.  So you might have nodes with diameters of .40", .42", .44", .46" and so on.  So, if you want to make, say, a scrolling matrix panel (see sample panel video we've produced for a customer to the right) with pixel nodes. 

What we found is that when we produced these panels from ABS plastic, a hard, stiff plastic sheet, they would hold perfectly but only if you cut the hole with .01-.02" of the actual diameter of the node.  Any more and the node would either fall out or would be wonky and not point straight out.  Any less and it was impossible to get the node in at all - in fact many people had to use lubricant just to get some of the nodes in a string into the holes (which were all exactly the same diameter).  So, it was clear that if we wanted to sell a product that would hold and mount RGB nodes from any vendor, that we would need a different method of mounting them. 

At first this seems simple - just find some plastic that can hold them, right?  Well, it turns out that isn't the case.  In holding pixel nodes, you have a number of factors to consider:

• They need to be held tightly so as not to point different directions, causing different levels of light output.
• The material needs to be able to "adjust" to slightly different sized nodes from different vendors.
• The material needs to stand up to UV and a wide range of temperatures (-20 to 130f).
• The material needs to be at a cost point that the final product is reasonably priced.
• The material needs to be strong enough to handle 5-15 pounds of nodes.
• The material needs to be strong enough when mounted to a frame or other material to resist tearing, sagging, stretching or failing in high wind loads.
• And finally the material needs to be easy to machine on our CNC equipment.

It's a tall order and that's why we've yet to offer a "standard", non-custom mounting frame.  So, starting in February, we spent countless hours researching the tens of thousands of materials out there that could be a possible match for the magical material so we can bring products based on nodes to you.  As of March 8th, 2013, we have narrowed the field down to two companies that make very specialized plastics that meet our needs and we are working with them to produce and test the plastics that we hope will solve this problem.  We hope to have material in the April/May time frame after testing is completed and products shortly there after.

  

So, what do we plan to produce with this magical plastic?  Well that's a good question.  We know that lots of you out there want a method of creating a simple scrolling matrix screen like what is shown in the video above, so that's a pretty much no-brainier - we'll offer complete kits to build exactly that. 

We also plan to offer a mini-tree that also holds the nodes and is curved like a circular tree with the nodes "studded" through out - this would be offered as a dumb and smart mini-tree kit.

As is often the case, once we have a starter product, often customers are the source of some of the best ideas out there that we could never imagine.  So, if you have ideas for a product that incorporates RGB nodes, smart or dumb, feel free to email us or leave feedback below on the blog.

29-Mar-2013 - Update:  We have released the matrix panel here:  http://www.holidaycoro.com/Pixel-Matrix-Mounting-p/265.htm
 

Thanks,

David

HolidayCoro.com